Question 1

What are the instructions for using QUARTZ 9H CERAMIC COATING(T1)?

Accepted Answer

Features:Quartz 9H ceramic coating is a mixture of nano structured quartz paint coating. It protects the surface from chemical and UV degradation as well as enhancing the depth and clarity of your car's paint, suitable choice for all installers eager to try coating products.Application Process:1. Wash your car before application,2. Make paint correction with abrasive and polishing compounds for best result.3. Clean surface with degreasant, make it clean and dry.4. Apply coating EVENLY section by section.5. Smear and inspect during drying. Check and correct for uneven smearing while coating have not been hardened.6. Wipe off with clean microfiber about 1 min later (Wiping time depends on local applying environment, for best result, better to wipe off before it becomes hard to remove )7. Leave 24 hours'curing time. ( For better effect, 2 layers is recommended,apply second layer after 2 hours)Notes:Do not wet or touch the paint work within 24 hours,lt is allowed to drive car after 2 hours.For max cure and hardness, do not wash car within 7 days!TIP: to speed up the curing time you can use an infrared heater set at 250-275°F(120-130°C) for 25 minutes on each area.

Question 2

What are the instructions for using SERUM 9H ULTRA CERAMIC COATING(T3)?

Accepted Answer

Features:Serum 9H ultra ceramic coating is an advanced version for Quartz ceramic coating. lt provides a superior form of protection for the paint, ensuring molecular level sealing and protection, very easy to clean while bring super water repellencyApplication Process:1. Wash your car before application.2. Make paint correction with abrasive and polishing compounds for best result3. Clean surface with degreasant, make it clean and dry.4. Apply coating EVENLY section by section.5.Smear and inspect during drying. Check and correct for uneven smearing while coating have not been hardened.6. Wipe off with clean microfiber about 1 min later (Wiping time dependson local applying environment, for best result, better to wipe off before it becomes hard to remove )7. Leave 24 hours'curing time. ( For better effect, 2 layers is recommended apply second layer after 2 hours)Notes:Do not wet or touch the paint work within 24 hours.It is allowed to drive car after 2 hours.For max cure and hardness, do not wash the car within 7 days!TIP: to speed up the curing time you can use an infrared heater set at 250-275°F(120-130°C) for 25 minutes on each area.

Question 3

What are the instructions for using GRAPHENE 9H PRO CERAMIC COATING(T5)?

Accepted Answer

Features:Graphene 9H PRO ceramic coating is the most durable paint protection product that has ever been released. lts strong chemical structure will equip with the perfect apparatus for the paintwork to bond to its surface and lock in an immaculate finish.Application Process:1. Wash your car before application.2. Make paint correction with abrasive and polishing compounds for best result.3. Clean surface with degreasant, make it clean and dry.4. Apply coating EVENLY section by section.5.Smear and inspect during drying. Check and correct for uneven smearing while coating have not been hardened.6. Wipe off with clean microfiber about 1 min later (Wiping time dependson local applying environment, for best result, better to wipe off beforeit becomes hard to remove )7. Leave 24 hours'curing time. ( For better effect, 2 layers is recommendedapply second layer after 2 hours)Notes:Do not wet or touch the paint work within 24 hours. lt is allowed to drive car after 2 hours.For max cure and hardness, do not wash the car within 7 days!TIP: to speed up the curing time you can use an infrared heater set at 250-275°F(120-130°C) for 25 minutes on each area.

Question 4

What are the instructions for using CERAMIC WINDOW COATING(TC)?

Accepted Answer

Features:Ceramic window coating is a ceramic coating based on nano technology for all glass surfaces. Glazed ceramic creates a super water repellent surface and prevents water spots,designed to be no wiper movement issues or noises, improving clearer visibility and increase safety of driving.Application Process:1. Clean windows before application.2. Use Tonyin glass polish compound with glass polish applicator block to remove oil film and make it clean and dry.3. Apply coating with applicator EVENLY on windows.4.Leave for 5-7 mins and wipe the surface with a dry microfiber5. Leave 24 hours' curing time.Notes:Do not wet or touch the applying surface within 24 hourselt is allowed to drive car after 2 hours.For max cure and hardness, do not wash the car within 7 days!

Question 5

What are the instructions for using PPF&VINYL WRAP CERAMIC COATING(TP)?

Accepted Answer

Features:PPF & Vinyl Wrap ceramic coating is a coating that is UV resistance, prevent from adging and acid rain,enhance the effects of ppf and vinyl wrap with features that will make the film last longer and easy for mainten-ance, while increasing the overall look.Application Process:1. Wash your PPF and Vinyl surface before application.2. Clean surface with degreasant, make it clean and dry.3. Apply coating EVENLY section by section. ( For hood.pls divide into 4 parts and apply one by one)4. Leave for about 1~2 minute and wipe the surface witha clean dry microfiber. (2 layers is highly recommend.ed, second layer should be applied after 2 hours)5. Leave 12 hours’ curing time.Notes:Do not wet or touch the applying surface within 24 hours. lt is allowed to drive car after 2 hours,For max cure and hardness, do not wash the car within 7 days!

Question 6

What are the instructions for using WHEEL&CALIPER CERAMIC COATING(TS)?

Accepted Answer

Features:Ceramic coating for wheel & caliper is the longest lasting and durable form of protection for wheel and caliper. lt has a higher resistance against high-temperature brake dust, micro marring and chemical attack, giving long-term ease of wheel cleaning without the need for harsh cleaning methodsApplication Process:1. Wash wheel and caliper before application,2. ake it clean and dry.3. Apply coating EVENLY4. For light color surface:No need to wipe off after applying.For dark color surface: Wipe off with clean dry microfiber after 3-5 mins.5. Leave 12 hours’ curing time.( For better effect, 2 layers is recommended)Notes:Do not wet or touch the applying surface within 24 hours.lt is allowed to drive car after 2 hours For max cure and hardness, do not wash the car within 7 days!

Question 7

What are the instructions for using LEATHER&DOOR PANEL CERAMIC COATING(TE)?

Accepted Answer

Features:Leather & door panel ceramic coating is a self-cleaning, antifouling protective coating for leather and door panels that restores new look of the sur-faces, retains its original texture, rich color and appearance, protecting against any dirt and stains.Application Process.1. Clean and dry the interior leathers and door panels thoroughly.2. Cover the parts that do not require installation with masking film.3. Fully wet the finger pocket microfibre applicator with coating, apply itevenly in a circular motion on surface of the leather and door panels Pls apply part by part.4. Wait 1-3 minutes according to the local temperature and humidity, andgently wipe the surface with a towel in one direction. ( Do not wipe thecoating completely clean, just wipe the surface evenly.)5. Wait for about 1 hour for penetration and drying, then apply the secondlayer.6. For original shiny surface, just wait for it to dry naturally. For original mattsurface,wipe the surface evenly in one direction, do not wipe the coatingcompletely clean, just wipe evenly.7. Do not touch with any liquid during this perod, leave it for 24 hours beforedriving the vehicle.Notes:Please do not apply on dashboard panel, or bright light will cause reflec-tion and affect driving safety.Pls do not apply on door panel surface that is hard plastic.Special leather needs to be tested on a small area before applying

Question 8

What are the instructions for using CERAMIC PLASTIC COATING(TR)?

Accepted Answer

Features:Ceramic plastic coating protects and restores faded color in the plastic and trim surface to its original rich color, bonds to the pores of unpainted plastic trim while forming ceramic coating on the surface.Application Process:1. Clean and dry the surface before application.2. Pour few drops of coating on the microfiber applicator blockand apply it gently on surface.3. Make sure to apply evenly on the surface4. No need to wipe off with microfiber, leave coating to dryNotes:Do not wet or touch the applying surface before it driescompletely.lt is allowed to drive car after it dries.

Question 9

What are the instructions for using CHROME&METAL CERAMIC COATING(TG)?

Accepted Answer

Features:Chrome & metal ceramic coating is a permanent easy-to.clean coating over polished metal and chrome. lt helps protect against finger prints, spotting, rust and corrosion,maintain reflective sparkle and shine for long timeApplication Process:1. Clean and dry the surface before application.2.Pour few drops of coating on the microfiber applicator block and apply it gently on surface.3. Make sure to apply evenly on the surface.4. No need to wipe off with microfiber, leave coating to dryNotes:Do not wet or touch the applying surface before it dries completely.lt is allowed to drive car after it dries

Question 10

What are the instructions for using CERAMIC MARINE COATING(TT)?

Accepted Answer

Features:Ceramic marine coating is professional grade coating that chemically bonds to the gelcoat, topcoat and other marine paint. lt has an exceptionally strong anti-static function that helps to keep surfaces dust-free and also contains a strong UV filter to help to prevent premature fading, its anti water spots quality makes the yacht very easy for maintenance.Application Process:1. Make surface correction with polishing compounds for best result.2. Clean surface with degreasant, make it clean and dry.3. Apply coating EVENLY section by section.4. Smear and inspect during drying. Check and correct for uneven smearing while coating have not been hardened.5. Wipe off with clean microfiber about 1 min later.( Wiping timedepends on local applying environment, for best result, better to wipe off before it becomes hard to remove )6.Leave 12 hours’ curing time. ( For better effect, 2 layers isrecommended, apply second layer after 2 hours)Notes:Do not wet or touch the surface within 24 hours For max cure and hardness, do not wash the yacht within 7 days!

Question 11

What are the instructions for using FABRIC COATING (TF)?

Accepted Answer

Features:Tonyin fabric coating is a solvent based protective coating designed for all textile, fabric, upholstery and sporous suraces. it creates an invisible laver which covers each individual fibre of the textile or leather to repels undesirable liquid, dirt and UV-radiationDirections:1. Shaking the bottle well, spray it fully and evenly on the surface.2. Spray some on the applicator, and apply the surface evenly to make it fully absorbed.3. Keep the surface still and let it air dry naturally to form a thin film for 12 to 24 hours.4. Test the water until the coating film dry and fixedPrecautionsDo not spray on glass during using, as it will affect vision, etcPlease use it in a well ventilated place.lf it comes into contact with the eyes accidentally, please rinse it immediately with plenty of clean water. lf you have other discomfort.please seek medical attention in time.Keep away from pregnant women,children and people with respira-tory diseases.Nano waterproof spray cannot cover materials with too large mesh.

Question 12

What are the instructions for using CERAMIC SPRAY SEALANT (TC03)?

Accepted Answer

Features:An advanced water based polymer containing UV inhibitors which adds ahydrophobic, self cleaning,durable layer of protection to all vehicle exterior surfacesDirections:1) Shake well and either spray directly to the surface or onto a clean microfibre applicator pad.2) For all surfaces application:For dry surfaces:spray product evenly over the surface,remove with a freshmicrofiber cloth after 2-3 minutes.For wet surfaces: spray product evenly over the surface, then wash with ahigh pressure water gun after 2-3 minutesPrecautions.Keep out of reach of children.In case of eye contact please rinse thoroughly with water

Question 13

What are the instructions for using GRAPHENE SPRAY COATING(TC04)?

Accepted Answer

Features:Graphene spray coating is the latest technological advancement to hit the automotive detailing market. As a booster and enhancer, it provides significantly better protection than traditional waxes and sealants. lt does this through graphene technology that allows the product to bond to entire your car suchas paint, wheels, glass, trim and leather at a molecular level with longer durability. This fills in microscopic pits and grooves in your paint leaving ahydrophobic surface that slick to the touch.Directions:1.Correct oxide layer of the paint, make the car clean and dry.2 Shake well, spray onto a microfiber sponge and apply to the surface.3.Wait for a few mins, wipe off with clean towel before it becomes hard to remove.Precautions:Ready to use, no need to dilute.Better not to touch with water within 12 hours after application Switch off the sprayer each time after usingAvoid direct sunlight while applying.Repeat application, 12 hours interval time is recommendedKeep out of reach of children.

Frequently asked questions